Outer PLC – TTGearLab

Tag: Outer PLC

2 Posts

Yinhe Mars (PLC) series [Lab Test Report]

November 7, 2023 — 18 Comments

Tibhar Fortino Pro [Lab Test Report]

October 30, 2019 — 18 Comments

grx009 on Donic Coton Relevant [Photos & Information]October 31, 2026
Thank you very much for the review! I've been thinking about trying this blade after the Xiom HAL, and it…
Murilo on Donic Coton Relevant [Photos & Information]October 28, 2026
I'm not sure I got this: does this have carbon or not? The old donic relevant (before coton) used to…
bravelywingedf7bcdc574c on Donic Coton Relevant [Photos & Information]October 27, 2026
Stop using AI to write this. But if you must, at least proofread before you publish. "As its name expresses,…
Vasyl on Donic Coton Relevant [Photos & Information]October 26, 2026
Thanks a lot! Currently I use this one. And now I can understand it better with numbers. Great job as…
Aditya on Donic Zentra Next Carbon [Photos & Information]October 26, 2026
Hello Dude, is ep/ec Number show the Blade stiffness? Higher number of ec/ep Is stiffer tahan lower number?
Jordi on Donic Whiper Inner Carbon [Photos & Information]October 25, 2026
La Ec es superior a la Ep o se ha cambiado el orden, con las gráficas vuestras actuales todas las…
Jordi on Donic Whiper Inner Carbon [Photos & Information]October 25, 2026
La Ec es superior a la Ep o se ha cambiado el orden, con las gráficas vuestras actuales todas las…
lombaxeuw on Donic Zentra Next Carbon [Photos & Information]October 25, 2026
Thanks for your continued efforts! I am always looking forward to reading your reports. You seem to post a lot…
Raj S Subramaniam on Donic Zentra Next Carbon [Photos & Information]October 25, 2026
Always good information
Jeff Huang on Performance Indices DB – Stiga BladesOctober 23, 2026
I have read through the valuable information you provided, and it seems that the weight of the racket may have…
TTEnt on andro Synteliac VCI OFF [Photos & Information]October 19, 2026
I've played with this blade for sometime now.Used Rakza Z on FH and Nuzn 55 on BH. With this setup…
ggreco66 on Butterfly’s Inner ALC blades [Comparison by Performance Indices]October 17, 2026
What about 729 Yellow ALC? It's a low cost inner ALC blade, but I feel very well with it, thanks.
bravelywingedf7bcdc574c on Performance Indices DB – Stiga BladesOctober 16, 2026
Could you review the Stiga I1?
Yen-Ning Tai on Butterfly’s Inner ALC blades [Comparison by Performance Indices]October 16, 2026
thank you for the analysis! I am learning these measurements to better help myself decide the next blade. it feels…
Shikhar Singh on Nittaku Septear [Photos & Information]September 30, 2026
Do you think the Nittaku Septear would still be Relevant in the coming years? I am planning to buy one,…
Bruce on Four powerful ‘inner type’ fiber blades [Comparison by Performance Indices]September 30, 2026
Hello, If I want to test this Stiga Cybershape Carbon, do you recommend using it with very hard rubbers (like…
Robert Hauke on adidas P7 [TTGearLab Works]September 30, 2026
Which new Rubber is like the Adidas P7?
Counter Topspin on Performance indices : the way to evaluate blade by measurementSeptember 25, 2026
Thank you very much for your reply. I'm really looking forward to seeing the results of your measurements. Do you…
Dolores on DHS Fang Bo B (7-ply) [Photos & Information]September 23, 2026
Actually i managed to find a close enough replacement after reading your review and that is Victas firefall VC. Not…
TTGearLab on Victas Swat [Photos & Information]September 22, 2026
Unfortunatly I couldn't have got that blade. When I tried it was out of stock, and the distributor doesn't have…
TTGearLab on Four powerful ‘inner type’ fiber blades [Comparison by Performance Indices]September 22, 2026
Thank you for information.
TTGearLab on Xiom Novus series [TTGearLab Works]September 22, 2026
Absolutely not! Its head size is 157mm x 150mm. (There can be small differences in actual products. for example 156…
TTGearLab on DHS Fang Bo B (7-ply) [Photos & Information]September 22, 2026
In fact, HL5 is the same blade as B2. The difference is in quality. So HL5 will be the solution…
TTGearLab on Performance indices : the way to evaluate blade by measurementSeptember 22, 2026
That differs case by case. Both of Ep and Ec increase when the thickness of blade increases. The ration is…
TTGearLab on Donic Whiper series [Lab Test Report]September 22, 2026
Thank you for comment! :-)